Boarding Up Windows And Doors Tools To Ease Your Daily Life Boarding Up Windows And Doors Trick That Everybody Should Learn > 자유게시판

24 hour boarding up service up windows and doors, Related Site, Before a Storm Hits

Before a storm hits and your windows are smashed, boarding up doorway them up and doors can protect your home from damage. To accomplish this, you will must have a few things on hand.

Find the height and width of the window, including the frame (not the trim or the masonry around the window). Take note of these measurements so that you won't forget.

Preparation

It is recommended to put up a put up a board on your windows and doors before an event like a hurricane or natural disaster. This will help prevent damage to property and reduce the loss of life. It takes an enormous amount of planning to put up windows. You must purchase and measure plywood boards and you must be aware of the specific dimensions of each window. It takes time to cut and install the boards in a proper manner. Fortunately this can be simplified by beginning the preparations immediately you learn of a possible storm forming in your area. By doing so, you can stay clear of a stressful last minute rush and make the process simpler for you and your employees.

Begin by listening to forecasters of the weather and following the guidelines laid out by your local government. The earlier you start the process the better, as it gives you enough time to collect and store the necessary materials without feeling pressured by a storm that is rapidly approaching. Depending on the severity of the imminent storm, you might require massive quantities of plywood to cover all of your windows. To ensure that you have the right size, you can make use of a tape measure to determine the width and height of each window opening. Be sure to include the trim or framing around each window, as well as any ledges with extended edges if they are applicable.

Divide the total width and the height of your window by 2 to determine the number of plywood sheets that you'll require. If your window measures a width of 16 inches, the thickness of each sheet is 8 inches. If your exterior is made of wood, make pilot holes in the plywood sheet to ensure it is aligned with the window frame below. This will help reduce the possibility of splitting when you screw in the screws.

For a window opening that is greater than the size of a single sheet of plywood can accommodate cut two sheets that are each half the size of the intended window and set them side-byside on the wall. Cut a 2 by 4 in (5.1 x 10.2 cm) of lumber to the length the connecting edge between the two sheets of plywood and then place it on top of the seam. Then, screw 2.25 in (5.7cm) screws into the plywood sheet and through the bracing to join the two.

Materials

To ensure safety and security, only use materials that are sturdy and won't break or splinter in high winds. The most commonly used material to board up windows is plywood, which is affordable easily available and simple to work with. Select plywood that is of the exterior grade (CDX) since it will be stronger and have fewer knots and warps. A stronger option is hurricane or storm shutters, which are installed over existing windows to provide more protection against glass shattering and the weather that can cause a lot of damage.

Once you've identified the position of the window openings take measurements of the height and width of each to determine how much plywood you'll require. Utilize a power drill to drill pilot holes into the sheets of plywood around each window at intervals of two inches. Before attaching the plywood, identify and mark the stud locations on the wall to ensure that the boards are anchored securely. If you have wood siding on your home, look for nailheads in order to determine stud location. You can also use your drill to find the locations of studs. Be sure to drive the screws into the framing, not the sheathing or trim. A plywood panel that is fastened to these materials could be a hazard in strong winds.

If the size of your window is too big for a single sheet plywood, cut two separate pieces that are each half the size you require and join them with 2 by 4 inches of lumber. Label each sheet of plywood to let you know which window it will be covering.

To affix the plywood panels to the wall, use corrosion-resistant screws that are long enough to get through both the sheathing and studs. To secure the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to penetrate the sheathing and the studs.

You should also think about installing polycarbonate security glass like DefenseLite on your windows that are primary. These transparent shields are secured to existing glass and shield your windows and doors. They are virtually indestructible and deter criminals from attempting to break into your home.

Installation

If you live in an area prone to hurricanes, or plan to move to one the best course of action is to put up a board on your doors and windows before the possibility of a storm is afoot. It's a project that can be done quickly and efficiently, but only if you take the time to measure and cut your plywood panels before the storm hits.

You'll require other tools as well which include the drill, a saw (or nail-driven hammer in the event that you don't have a power tool) as well as an erecting level, gloves and safety glasses. It's also a good idea for the plywood to be coated with sealant in order to make it waterproof.

Start by taking measurements of the width and height of each window's opening, and then cutting the plywood sheets so that they can fit inside the frames, with a 4-inch overlap on all sides. This is best done on-site because you have more control over the exact dimensions.

Utilize a circular or track saw to cut the boards to the right size, and remember that you'll have to sand them down once they're put in. Once the boards are in place, screw the 3-inch stainless steel hanger screws into the framing posts around each window. Use washers on each bolt and wing nuts to ensure they are secured. Make sure that each screw penetrates the studs at a minimum of two inches to ensure the board is strong enough to resist strong winds.

If you're building using concrete blocks, you can join the plywood with galvanized pan head screws which are driven into the edges of the panels into bricks or cinder blocks. It is also necessary to drill pilot holes in the masonry and then insert corrosion-resistant screws into the holes. It's a project that can take anywhere from three to four hours per window, so it's important to start the process when you learn that a hurricane warning has been issued. This will give you time to finish the project before the storm hits.

Maintenance

It is recommended to board up your doors and windows prior to the onset of a severe storm. This will allow you to avoid costly repairs and safeguard your home from further damage caused by rain, wind debris, flying objects and other factors.

The right materials will make boarding simpler and faster. It is essential to precisely measure the windows. This will ensure that the plywood or OSB is snugly fitted and won't be removed easily. If you are using plywood, make sure you use exterior grade sheets and consider adding an additional protective finish.

After you have the OSB or plywood taken measurements, mark the locations where the screws will go into the board. Then, use a drilling machine to pre-drill holes in the plywood at 12-inch intervals. You can then use hanger bolts to secure the boards in an emergency or emergency boarding up cost situation. Once the storm has passed and you've received the all-clear by local authorities, take off the hanger bolts, but leave them in place for future emergency boarding up service situations.

Next, install the plywood panels above the windows. Be prepared to work in pairs. If you're using wood, make sure you sand the edges to ensure they're smooth and won't scratch your paint or trim. Then, use corrosion-resistant screws to join the plywood with the pilot holes. If your home has shingles made of vinyl on it, then attach the plywood directly to the shingles and not to the wood framing.

In addition to keeping out the elements of weather and water elements, a boarded-up window is also a great way to prevent burglary. The burglars will be more likely to target a structure with a damaged window or one that's not secured. Additionally, they are more likely to break into the store with a boarded up window than one without. This is something that business owners in retail should consider very seriously.