Boarding Up Windows And Doors Techniques To Simplify Your Daily Life Boarding Up Windows And Doors Trick Every Person Should Learn > 자유게시판

commercial boarding up service up windows and doors (click the up coming web site) Before a Storm Hits

Before a storm hits the windows and doors can protect your home from damage. You will need some items to accomplish this.

First, measure the width and height of the window, including the framing (not the trim around it or masonry). Keep these measurements in mind so you don't forget.

Preparation

It is always recommended to secure doors and windows prior to a storm or other natural disasters strike. This will reduce property damage and reduce the risk of death. It requires lots of planning to build a board around windows. You will need to purchase and measure plywood boards, and you must be aware of the exact dimensions of each window. It also takes time to cut the boards and put them up them correctly. The process can be streamlined by beginning the preparations immediately you hear of an approaching storm. If you do this, you can avoid a stressful last-minute rush and make the process much easier for yourself and your employees.

Begin by listening to weather forecasters and observing the guidelines of your local government. The earlier you start the process the better, as it gives you enough time to collect and store the necessary materials without feeling pressured by a rapidly approaching storm. Depending on the severity of the pending event, you may need huge quantities of plywood to cover all your windows. To ensure you get the right size, you can make use of a tape measure determine the width and height of each window opening. Be sure to take into account the trim or framing surrounding each window, as well as any sills that are extended if applicable.

Divide the total width and the height of your window by 2 to determine the amount of plywood sheets that you'll need. If your window measures a width of 16 inches, the thickness of each sheet is 8 inches. If your exterior is made of wood make pilot holes into the plywood sheet so that they align with the window frame below. This will prevent the chance of splitting when you insert the screws.

If you have a larger window opening than one sheet of plywood can handle, cut two sheets of plywood that are half as big as the window you want to use. Then, place them side-by-side on the wall. Cut a piece 2 by 4 in (5.1 10.2 cm) 10.2 cm) of lumber to the length of the connecting edge between the two sheets of plywood and place it on top of the seam. Then, screw 2.25 in (5.7cm) screws into the plywood sheet and through the bracing to join the two together.

Materials

To ensure security and safety, only use materials that are sturdy and will not break or splinter in strong winds. The most popular material used to board up windows is plywood, which is inexpensive easily available and simple to work with. Select plywood that is exterior grade (CDX) since it will be stronger and contain fewer warps and knots. Storm shutters or hurricane shutters are more durable options. They can be put in over existing windows and offer greater protection against broken glasses and inclement weather.

Once you've determined the location of your windows then measure the width and height of each one to determine how much plywood you will need. Use a power drill drill pilot holes into the plywood sheets around each window at intervals of 2 inches. Mark the walls with studs prior to attaching the plywood to ensure that the boards are secured. If your home is constructed with wood siding, search for nailheads that might indicate the locations of studs. You can also use your drill to locate the locations of studs. Be sure to drive the screws into the framing rather than the trim or sheathing; a plywood panel fastened only to these materials could become dangerous in winds that are strong.

If your window is too large for one sheet of plywood, you can cut two pieces of plywood each half of the size needed and join them with 2 by 4 inches of lumber. Label each plywood sheet so you know what window it will cover.

To secure the plywood panels to the wall, make use of corrosion-resistant screws that are long enough to get through both the sheathing and studs. Make sure to drive the screws into the studs so that they are about half as deep as the thickness of the plywood however, be cautious not to go too far and harm the underlying structure of your home.

You should also consider installing polycarbonate security glass such as DefenseLite on your primary windows. These transparent shields are bonded over existing glazing and protect your windows and door. They are virtually impervious to breakage and can deter burglars from breaking into the house.

Installation

If you live or intend to move to a place susceptible to hurricanes and are concerned about the storm it is recommended to board up your doors and windows. It's a project that can be done quickly and effectively however only if you take the time to measure, cut and label your plywood before the storm arrives.

You'll also need a few other tools, including drills (or nails and a hammer for those who don't own a power drill), a saw, tape, a level, gloves and safety glasses. It's also a good idea to allow the plywood to be coated with sealant in order to make it waterproof.

Start by taking measurements of the width and height of each window's opening, and then cutting your plywood sheets so they fit inside the frames, with a 4-inch overlap on all sides. It's best to do this on the spot, as it gives you more control over the exact dimensions of the plywood.

Cut the boards to the size you want using a circular or track saw. Once they're installed you'll need to sand all of them. Once the boards are in place put the 3 inch stainless hanger screws made of steel into the framing posts around each window. Use washers to secure each bolt and wings nuts. Make sure that each screw gets through the studs by at least 2 inches to ensure that the board is strong enough to withstand high winds.

If you're building using concrete blocks, you can attach the plywood to the structure with galvanized pan-head screws pushed through the edges that are overlapping of each panel into masonry blocks or cinder blocks. You'll also need to drill pilot holes into the masonry and then screw corrosion-resistant screws through the holes. This project can take three hours per window. It is important to begin the project as soon as a hurricane warning has been issued. This will allow you enough time to complete your project prior to the time when the storm is expected to hit.

Maintenance

If you're a homeowner or business owner, you should have the right supplies to put up a board around windows and doors ahead of a severe storm. This will help you to avoid costly repairs and safeguard your home from further damage that could be caused by rain, wind flying objects, and other factors.

The proper materials can make boarding up more efficient and speedier. It is essential to accurately measure every window. This will ensure that the plywood or OSB will fit snugly and won't be able to be removed easily. If you are using plywood, make sure to use sheets of exterior grade and think about adding a protective finish.

Note the locations where screws are to be inserted into the board once you have measured the OSB or plywood. Then, you can use a drill to pre-drill holes into the plywood at 12-inch intervals. This allows you to securely fasten the boards with hanger bolts in an emergency boarding up or in the event of a disaster. After the storm has gone away and you've received all-clear from local authorities, remove the hanger bolts but keep them in place service for boarding up windows future emergencies.

The next step is to put the plywood panels on top of the windows. This is a two-person task So, be prepared prior to starting. If you're using plywood, make sure to sand down the edges to ensure they're smooth and won't scratch your paint or trim. Then use corrosion-resistant screws to join the plywood with the pilot holes. If your home is covered with shingles made of vinyl it is recommended to nail the plywood to the shingles rather than the wood framing beneath.

A window that has been boarded up may be used to deter burglars. Burglars are more likely take aim at a structure with a broken or unlocked window. They're also more likely to enter a store that's been closed than one without. This is something that retail business owners should take very seriously.