10 Tell-Tale Signs You Need To Know Before You Buy Door Lock Change > 자유게시판

How to Do a Door Lock Change

Changing your door lock is a simple and inexpensive method to increase the security of your home. However, the procedure is not for all. It requires some skill and patience.

The cylinder is contained within the knob's body. The cylinder is responsible for recognizing the key as it is inserted into the lock.

Remove the old lock

The first step to replace the door lock is to remove the lock that was previously in use. It's a straightforward process, however you should keep some things in mind. Make sure that the new lock fits your door. This will ensure that it fits properly and doesn't leave a gap around the deadbolt plug or latch.

After you have removed the latch plate, you will be required to search for two screws or bolts on the inside of the casing that are holding the casing together with the lock halves. Unscrew them using a screwdriver and then pull the lock out of the door. If you have a mortise lock there could be a set screw located at the base of the handle, which binds it to the spindle. Use a screwdriver to unscrew the screw, and then take out the doorknobs.

You must also remove the latch and deadbolt plug from the hole in your door jamb. Install the new lock. If you are replacing a mortise lock you must also measure the distance between the lock case and the edge of your door to ensure that the new lock will be able to fit.

You may want to replace replacement window locks lock (zenwriting.Net) your lock for various reasons, such as when you suspect that someone else has the key or if you've new roommates. In any case, you can save money by taking the lock off yourself, rather than hiring an expert to do it. It's much easier than people think and can be accomplished in just a few moments.

Remove the handle and trim of your door. With a flat screwdriver take off the trim. You should be able to twist off most of it, and in some instances, the handles might come off entirely. Next, look for a hole on the inside of the handle, and insert straightened clips into it. This will activate the release mechanism, which allows you to remove the handle. The next step is to look at the interior side of the lock for a small tab and press it with a flat screwdriver. After the spindle is removed, you can then remove the cylinder and the housing.

Making a choice for a new lock

When it comes to choosing the right lock for your home you have a variety of choices. Look at different types of locks, and select one that fits the style of your door. Take into consideration the backset, which is the distance between the edge and the middle of the hole in the lock. Also consider the cross bore, a small hole at the edge of your door's frame. Also, ensure that you choose a lock that will accommodate the door's thickness as well as swing.

The majority of door locks have been graded by BHMA and the American National Standards Institute to give you an idea of how well they are able to withstand the rigors of use and how difficult to pick or disable. A grade 3 lock could be ideal for a quiet suburban apartment complex, whereas an entry grade lock could stand up to the traffic that is frequented by a storefront on a busy city street.

Most smart door locks require a digital code to open. If you're worried about hacking, or any other security concerns, consult a professional locksmith.

Replacing the cylinder

It is easy to replace a damaged or broken door lock cylinder using an easy DIY project. It is essential to choose the right cylinder and follow the instructions. First, take off the handle or knob if it is present. Then, using a screwdriver, take off the trim around the lock cylinder. After the trim is removed, you will be able to access the screws that secure the cylinder and remove them using a flathead screwdriver. The cylinder is then gently pulled from the door.

Before installing the new cylinder, be sure it's the correct length for your door. Measure the distance from the center to the left and right sides of the cylinder using a tape measure. Then, purchase another cylinder that has the same measurements. This will prevent cylinders from snapping when doors are kicked or the key becomes stuck inside.

Install the replacement locks for double glazed windows cylinder into the door and then turn the key. This will align the cylinder with the carriage which is located usually on the outside of your lock. Then, loosen the set screw, which should be just a few turns in the head. It is also necessary to loosen the screw on the door's edge which secures the case if there is one.

After removing the lock cylinder after which you can replace it with a new lock by slipping the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the bracket that connects the cylinder to the stem of the lock indicator, which you can do by pulling out three small tabs on back of the cylinder with needle-nose pliers. Then, you can connect the remaining smaller bracket to the back of the cylinder. Then, you should reinstall the latch plate and strike plate, as well as the retaining rings that are connected to the top of the lock the cylinder.

Installing a new lock

If you're replacing an existing lock, you should start by measuring the width of your door. Most locksets for residential use are designed for doors with a thickness of 1 3/8 to 1 3/4 inch. If your door is more than 1 3/8 to 1 3/4 inches, you'll need a stronger door kit. This will require longer screws, or a longer spindle extension or the tail piece for door knobs.

Most replacement upvc window locks come equipped with a comprehensive installation guide to help you. Read the instructions carefully before starting the process to make sure that you are following all of the necessary steps. The manual will give you a good idea of the amount of skill that is required to finish the task. If you're changing locks for the first time, you might need to seek out an experienced friend for assistance.

It's a great idea seal the openings of the old hardware prior to installing the new lock. This will keep the screws from falling out of the holes and protect any tiles you might have put in the area. It also protects against possible damage caused by rust, dirt, and grime. SECURAM Touch comes with a strip of painter's tape, which is designed to be used for this purpose, but you can also use gaffer's tape as well as masking tape when you have it.

After removing the screws that hold the lock's interior to its exterior, remove the lock immediately. It is important to do this quickly to avoid the lock from accidentally closing and damaging the mechanism.

Install the new latch bolt into the upper cross bore of your new lock, if it has one. Make sure to place it in the correct location, which is indicated by an arrow. Then, you can screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plate to the door jamb. Test the deadbolt a few times, throwing it around to make sure it extends into the strike plate. Follow the directions included with your electronic smart lock to program it. This involves downloading an app and registering your e-mail address, verifying you identity, and connecting to the wireless network to connect your device.