Three Greatest Moments In Fix Door Hinge History > 자유게시판

How to Fix a Loose Door Hinge

Most homeowners can fix hinges that are loose. If the screw holes have been stripped and will not hold screws, you may need to use wood glue and dowels to fix the door hinge.

Remove any surface that has rust. This will allow the dowels to remain in place and provide them a solid base to rest on.

Take the Hinges off

Many hinges for doors can be removed, making it easier to move doors from one side of the frame to the opposite side or take the entire composite door hinges off when needed. The removal of the hinges is simple for anyone with a little patience, but you have to know how to do it properly.

If the hinges are painted you will need to remove the paint prior to attempting to remove the pins. If you don't, the paint could be smashed off and scratch your door when you attempt to lift it. To break the paint seal, place the hinges in a stainless steel dish and fill the pan with water until the hinges are completely submerged. Let the hinges sit in the pan for approximately 30 minutes. The heat from the water will soften the paint and make it easier to get rid of the pins.

After the pins have been loosened, remove the hinges and the frame from the door. You can use a screwdriver to get the job done, but it is recommended to use a magnetic screwdriver for this project. This type of screwdriver is specifically designed to grab metal screws and aid you in getting the job completed much quicker.

It is a good practice to spray some lubricant on the hinges prior to attempting to remove them. A simple lubricant will allow you to move the process along faster and remove the pins and screws with ease. You can find this type of lubricant in most hardware and home improvement stores.

Keep in mind that the number of hinges you will need will differ based on the replacement upvc door hinges's type and the setting. Doors with solid cores and heavy weights will require more hinges, whereas lighter and hollow-cored doors may only require two or three hinges.

It is also important to know the various types of hinges so you can decide which one will best suit your needs. Exterior hinges are designed to support the weight of a door, whereas hinges for interior use must be able support lighter loads.

Reattaching the Hinges

Sometimes, a hinge on a door will get looser and eventually begin to hang out of alignment or sag. It can be a big problem, but the fix is usually easy. A simple tightening can solve the issue. However in the event that the screw holes are stripped out, this may be more difficult. A wood dowel can be used to tighten the holes again.

Start by drilling the old hole using a drill bit close to the size of the new screw (normally 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a snug fit, the dowel should be cut to the same length as the screw. Then, you can reinstall the screw and tighten it until the desired tightness. If the door continues to bind up, add another dowel to the gap. Repeat the process. Be sure to shut the door slowly so that you can check the perimeter clearances after each adjustment.

You could also use a wood plug instead of the dowel. It's also possible however it will take a bit longer to install. You can insert the wood piece that has been whittled down to the proper size. If you don't have a wooden tool, you can also use toothpicks or wooden matches as well.

Make use of a countersink in order to make the hole smaller than the head of screw after you have put it back in place. This will prevent the screw from hitting the edge of the doors when they are closed and opened. This will aid in tightening the screw prior to installing the hinge.

After reinstalling the hinge, apply lubrication to the hinge using an oil-based lubricant that is dry. This will prevent it from becoming stuck in the future. Products like PB Blaster or Liquid Wrench are good options. Apply a thin layer of it and allow it to soak into the hinge barrel for around 15 minutes.

Refinishing the Hinges

If you're not sure if you're ready to replace the hinges on your door, you can make a few minor repairs. Check that the screws that hold the hinge plate to the door frame as well as the frame are in good condition. If they're loose, tighten the screws with a power drill or screwdriver. Be cautious not to tighten the screws so tight that they cause gaps at the trim joints, or even worse, strip the threads.

If the problem is the hinge plates are splitting, you can reattach the plates by applying wood glue to the side of them and inserting toothpicks or wooden dowels into the holes. Dowels and toothpicks provide an solid foundation for the screws, and prevent the plates from shifting as you insert them. Let the glue dry before attaching the hinge.

The screws may also be damaged or missing. This issue can be resolved by replacing the screws. Make sure the drill bit is the same size as the screw hole to prevent drilling into the hinge or jamb.

Close the door after you've reattached your hinge and check the gap between the frame and the door. It should be approximately the thickness of one nickel all the way around or less if there's an existing gap created by a previous door that hung improperly. If the hinges were put in place correctly, this shouldn't be an issue.

If the hinges are still loose, you could add an extra thick hinge between the hinge plate's surface and the mounting surface. This will give the hinges a little more room. You can also remove the hinge pin and then pound it down with a heavy hammer to tighten it or use the hinge of a different type. You can also lubricate your Casement Windows hinges with mineral oil or jojoba to decrease friction and help keep them in their place. Lubricating your hinges frequently can keep them from becoming stiff and squeaky, and can also prolong their life.

Cleaning the Hinges

The constant movement of a hinge creates friction, which attracts dust particles. These particles can become stuck and accumulate over time in the moving parts of door hinges if they're not regularly cleaned and lubricated. In the end the hinge can become stiff and creaky and its appearance could be damaged quickly. Regular cleaning, lubrication, and inspection can help preserve the quality of door's hinges and ensure their proper function.

Check the hinges to see how much rust has formed on their surfaces. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you are able to save the hinges, first brush away loose rust using steel wool and wire brushes. Then, apply a commercial rust remover or a homemade solution such as lemon juice on the hinge. Let the rust-removing solution remain on the hinges for a few minutes to penetrate and dissolve the remaining rust.

If you do not want to spend the time and money to replace hinges, simply tightening the screws will restore the replacement window hinges' functionality. If you have stripped the screws however, it could be necessary to add a wooden dowel or shim to the hinge. Dowels made of wood are round pieces of wood in the form of rods that are available in various lengths and diameters. They are available at home improvement centers as well as woodworking supply and craft shops, or on the internet.

You can also make an shim using made of plastic or metal depending on the type of hinge you are using. To make a dowel, cut a piece made of wooden dowel or other sturdy material to the desired size. You can then dip the dowel in carpenter's glue before inserting it into the stripped hole, allowing the glue to hold the dowel in the right position.

Before you start cleaning the hinges, place down a towel or a paper towel to shield floors and other surfaces from drips and spills that could happen. After the area has been secured then clean the hinges using an absorbent sponge or a soft cloth that has been soaked in mild cleaner or vinegar to remove built-up dirt, grime and tarnish. You can use a toothbrush or small brush to get into difficult-to-reach areas in tight spaces and crevices.