How To Solve Issues Related To Door Lock Change > 자유게시판

How to Do a Door Lock Change

Changing your door lock is a simple and inexpensive way to increase the security of your home. This process isn't for all. It requires a certain amount patience and skill.

The cylinder is contained within the knob's body. The cylinder is responsible for recognizing the key when it is put into the lock.

Removal of the old lock

First, remove the lock that was previously in place. This is a relatively easy process, but there are some things to be aware of. Make sure that the new lock is compatible with your door. This will ensure that it fits snugly and doesn't create a gap around the deadbolt plug or latch.

After you have removed the latch plate, you'll have to look for two screws or bolts on the inside of the casing which are holding the casing in place with the lock halves. Take these screws off using a screwdriver before removing the lock off the door. If you have a mortise locking, there could be a set screw located at the base of the handle that binds it to the spindle. Make use of a screwdriver for removing this screw, then pull out the doorknobs.

It is also recommended to remove the latch and deadbolt plug from the hole in the door jamb. Then, you are able to install your new lock. If you are replacing a mortise lock you must also measure the distance between the lock case and the door's edge to ensure that your new lock will be able to fit.

You may want to replace your lock for various reasons, for instance, if you suspect that someone else is holding the key or you've an incoming roommate. In any case, you can save money by removing the lock yourself instead of paying a professional to do it. It's much simpler than you think and can be completed in a matter of a few minutes.

Begin by removing the trim and handle from your door. Then, you can pry the trim off with a flat screwdriver. You should be able to twist off the majority of it, and in some instances the handles could come off completely. Next, search for a pinhole on the inside of the handle and insert straightened clips into it. This will activate the release mechanism and allow you to remove the handle from the door. Next, examine the inside of the lock to find a small tab that you can press with a flat screwdriver. After the spindle is removed, you are able to remove the cylinder and the housing.

Making a choice for a new lock

You have many options when it comes time to pick a new lock. Consider different types of locks, and find one that matches your door's style. Consider the backset (the distance between the door's edge and the center of the hole for the lock) and the cross bore (small hole that runs along the edge of the door frame). Also, make sure to select a window lock repair cost that is able to accommodate the door's thickness as well as swing.

Most door locks are assessed by BHMA and the American National Standards Institute to provide you with an idea of how they stand up to use and how difficult they are to pick or disable. A grade 3 upvc window lock mechanism replacement might be ideal for a quiet suburban apartment complex, whereas a grade 1 lock might be more able to withstand the traffic near a busy retail storefront on a busy street.

Most smart door double glazing window locks replace require digital code to open. If you are worried about hacking, or other security issues, talk to a professional locksmith.

Replacing the cylinder

If your door lock's cylinder is damaged or broken you can repair it within a matter of minutes by completing a do-it-yourself project. It is important to select the appropriate cylinder and follow all instructions. First, remove the knob or handle if it is present. Then, using a screwdriver, remove the trim that is around the lock cylinder. After the trim is removed, you can access the screws that keep the cylinder in place and remove them using the flat-head screwdriver. The cylinder can then be gently removed from the door.

Make sure you measure the length of your new cylinder prior to installing it. Take a measurement of the distance from the center to the left and right sides of the cylinder with a tape measure. Purchase a new cylinder which has the same measurements. This will stop cylinders from snapping when the door is kicked or the key becomes stuck inside.

If you have a replacement cylinder, insert it in the door and turn the key. This will ensure that the cylinder is in alignment with the carrier, which is normally located on the outside of the lock. You can then loosen the set screws, which should be only a couple of turns into the head. If there is a screw on the outside of the case that is holding the door, you will have to loosen it.

You can replace the lock cylinder you have used with a new one by inserting it into the case and tightening the set screws. Installing the part that connects the cylinder to an indicator stem for a lock is also crucial. You can do this by pulling three small tabs in the back of the cylindrical with needle-nosed pliers. Attach the smaller bracket to the back of the cylinder. You must then install the latch plate and strike plate, along with the retaining rings that are connected to the top of the lock the cylinder.

Installing a new lock

Begin by measuring the width of your door if you are replacing an existing lock. The majority of residential locksets have a thickness of 1 3/8 inch to 1 3/4 inches. If your door is more thick, you will need a door kit that is thick and includes longer screws and an extended tail piece (for door knobs) or spindle extension (for deadbolts).

Most locks come with a thorough installation guide to assist you. Be sure to read the instructions thoroughly before starting the process to make sure that you've followed all of the necessary steps. The booklet will give you a good idea of the amount of skill that is required to finish the task. You might want to ask a friend who has experience changing double glazing window locks repairs for help if you are changing a lock the first time.

Before installing the new lock it's a good idea to cover the holes with tape the old hardware. This will stop screws from falling through the holes and will also protect any tiles you may have put in. It will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip painter's tape designed to be used to protect your painter's tape, but you can also use gaffer's tape or masking tape when you have it.

After you have removed the screws that hold the inside of the lock section to the outside side, pull it straight away. This should be done swiftly to prevent the lock from closing accidentally and damaging the mechanism.

If the new lock comes with an latch bolt, install the new bolt into the upper cross bore. Make sure that you place it in the correct location, which is indicated by an arrow. Then, slide the latch plate over the bolt and screw it in place.

Attach the deadbolt to the door jamb. Check the deadbolt several times by throwing it to make sure it extends into the strike plate. Follow the directions that come with your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying your identity, and connecting to the wireless network in order to connect your device.