Guide To Fix Door Hinge: The Intermediate Guide For Fix Door Hinge > 자유게시판

How to Fix door hinge a Loose Door Hinge

Most homeowners can repair hinges that are loose. However, if the screw holes are damaged and can't hold screws, you may need to put in dowels and wood glue before you can install the hinge.

Remove any surface corrosion. This will allow the dowels to remain in place and provide them a solid base to grip into.

Eliminating the Hinges

A variety of door hinges can be removed, making it simpler to move a door from one side of the frame to the other or remove the entire door in the event of need. Removing the hinges is fairly simple for anyone with a bit of patience, although you have to know how to do it properly.

If the hinges have been painted, you'll need to get rid of the paint prior to trying to remove the pins. If you do not, the paint may be smashed off and scratch your double glazing door hinges when you try to lift it. To break the seal of the paint put the hinges in a stainless steel pan and fill the pan with water until the hinges are completely submerged. Let the hinges sit in the pan for 30 minutes. The heat of the water will soften the paint making it easier to remove.

Once the pins are loosened, remove the hinges and the frame from the door. It is possible to use a regular screwdriver, but a magnetic screwdriver is recommended for this job. This type of screwdriver has been specifically designed to take out metal screws and aid you in getting the job accomplished much faster.

Before you attempt to remove the hinges, it is a good idea to spray them with oil. A simple lubricant can make the process to go more quickly and help you remove the screws and pins. You can find this kind of lubricant at a variety of hardware and home improvement stores.

It is important to keep in mind that the number of hinges you'll need will vary depending on the door's type and its configurations. Heavier and solid-cored doors will require more hinges while hollow-cored doors that are lighter may only require two or three hinges.

Understanding the different kinds of hinges can help you determine which one is best for your needs. The hinges on the exterior are designed to hold the weight of a door, whereas hinges for interior use must be able to handle heavier loads.

Reattaching the Hinges

Sometimes a door hinge will loosen over time and start to hang in a crooked manner or sag. This can be a problem, but it's usually easy to solve. Most of the time, a simple retightening of the screw will fix the problem. However, if the screw holes are ripped out, this may be more difficult to accomplish. A wood dowel could be used to tighten these holes again.

Start by drilling out the hole you had previously made using a drill bit that is similar to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length similar to the screw to ensure a snug fit. Install the screw again, and tighten to desired level of tightness. If the door continues to have the tendency to be bowed, then add another dowel to the gap and repeat the process. Be sure to close the door slowly in order to verify the clearances at the perimeter after each adjustment.

Another option is to just utilize the wood plug instead of dowel. This will work similarly, but it may take a little longer to set up. You can tap in the wood piece which has been cut to the proper size. If you don't have a woodworking instrument or toothpicks, you can make use of toothpicks or matchsticks made from wood.

Once you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the screw's head smaller so that it does not rub against the edge of the door when it's opened and closed. This will allow you to tighten the screw prior to installing the hinge.

After you have reinstalled the hinge, be sure to lubricate it using a dry lubricant to ensure that it doesn't get stuck in the future. Products such as PB Blaster or Liquid Wrench are good options. Apply a thin layer and allow it to soak into the hinge barrel for around 15 minutes.

Refinishing the Hinges

If you're unsure whether to replace hinges, you could try a few fixes. Make sure the screws that secure the hinge plate to the door frame and frame are tight. If they're loose, tighten them with an electric drill or screwdriver. Be cautious not to tighten the screws to the point that they create gaps in the trim joints, or worse, strip the threads.

If the issue is that the hinge plates are breaking away from the door and jamb, you can reattach the hinges by applying wood glue to the back of the plates and then inserting wooden dowels or toothpicks into the holes. The toothpicks and dowels provide a solid foundation for the screws, which will stop the plates from moving as you insert them. Allow the glue to dry before attaching the hinge.

The screws could also be smashed or gone. It is possible to fix this issue by replacing the screws with longer ones. Make sure the drill bit is similar to the size of the screw hole to prevent drilling into the hinge or jamb.

Close the door once you have reattached your hinge and examine the gap between the frame and the door. It should be around the thickness of a nickel all the way around, or less if there's an existing gap caused by a previous door that was not properly hang. If the hinges were set up correctly, this shouldn't be an issue.

If you notice that the hinges remain loose, try adding the thicker shim of the hinge between the hinge plate and the mounting surface to add an extra inch of space. You can also take off the hinge pin, then pound it down with a powerful hammer to tighten it or use an entirely new hinge. It is also possible to lubricate the hinges using mineral or jojoba oil to lessen friction and assist in keeping their place. Periodically lubricating your hinges can aid in keeping them from becoming stiff or squeaky, and can also extend their life.

Cleaning the Hinges

The friction generated by the constant movement of a hinge attracts dust particles. These particles can get stuck and accumulate over time in the moving parts of hinged door repairs hinges if they are not cleaned and lubricated regularly. In the end, the hinge becomes stiff and creaky, and its appearance can be damaged quickly. Regular cleaning, lubrication, and inspections will ensure the quality and function of hinges that are attached to doors.

Examine the hinges for rust accumulation. If the rust has corroded to the point of destroying the surface of the hinge barrel or screw holes, you'll require replacement of the hinges. If you are able to save the hinges, begin by brushing off any loose rust with steel wool and a wire brush. Apply a commercial rust removal solution or homemade solutions like lemon juice to the hinge. Allow the rust-removing solution to sit on the hinges for several minutes in order to penetrate and dissolve the remaining rust.

If you don't want to spend the money and time replacing hinges on double glazed windows your hinges, simply retightening the screws can bring back the hinge's functionality. It may be necessary to add an shim of wood or a dowel to the hinge in the event that the screws have been degraded. Wooden dowels come in round rods of varying lengths and sizes. They are available at home improvement stores as well as woodworking supply and craft shops, or on the internet.

A shim may also be made from a piece of plastic or metal, depending on the kind of hinge you have. To make a dowel cut a piece of wood dowel or another sturdy material to the size you want. You can then dip the dowel in carpenter's glue before inserting it into the cut hole, allowing the glue to hold the dowel in place.

Before you begin cleaning the hinges, place down a towel or a paper towel to shield floors and other surfaces from spills and drips that may happen. After protecting the area clean the hinges with an easy sponge or cloth coated with mild cleaner to get rid of dirt and grime. Also, tarnish and rust can be removed. You can make use of a toothbrush or a small brush to reach hard-to-reach spots in tight spaces and crevices.