You'll Never Guess This Replace Door Lock's Tricks > 자유게시판

How to replace door lock Door Locks

Your first protection is your door lock. It will prevent unauthorized access into your home. Locks might need to be replaced because of signs of wear and tear or other events such as moving into a new home or a break-in.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will assist you select the appropriate lock.

Deadbolt

Installing a deadbolt can be a ideal way to secure your door against intruders. When the bolt is extended into the strike plate of the doorframe it makes it more difficult for an intruder to break through the door. A single-cylinder deadbolt is activated with a key on the exterior and the thumb-turn mechanism located on the interior. A deadbolt is only effective only if it's correctly installed, though.

You will first need to determine if the door has an existing hole for a deadbolt or if you'll need to drill it out. With the template included with the lock installation kit mark the location of the hole for the deadbolt on the door's surface. Utilize your tape measure to determine the height of the deadbolt. Then, mark this height on the side of the door. Use the speed square to draw a straight line across the mark you made for the bolt hole.

Then using an electric drill, bore out the hole until it reaches the opposite side of the door. This could take a while. Then, sand down the hole and the edges of the door until it's smooth. It's also an excellent idea to stain or paint the door at this point.

Once the door is ready, remove any screws visible on the deadbolt. This will reveal the front and rear assembly of the deadbolt and its bolt inside. Then, remove the bolt and replace lock upvc door it with a new one that is compatible with the door hardware. The bolt is usually connected to a setplate, which you will have to remove. After that, you'll have to chisel the surface of the composite door replacement lock frame for the strike plate.

If your strike plate is misaligned It's likely that the previous installer didn't correctly mortise it or a weatherstripping popped up and changed the strike position. You will need to re-mortise the strikeplate and possibly even the deadbolt itself to fix this issue. Once this is completed Test the deadbolt by closing it and locking it. Make sure that the bolt is extending into the strike plate, and then test the key to make sure it is able to open and close smoothly.

Knob

If the knob on your door is damaged it could make your business or home less secure. It could also make opening or closing the door more difficult, which is why it is a good idea for you to Replace lock on upvc door it. It shouldn't take longer than 30 minutes. Use pliers or a screwdriver to remove any knobs or handles. Be careful not to harm the other components of the door.

Before you start you'll need to spray WD-40 or some other dry lubricant onto the mechanism of the knob on your door. This will help the new lock to slide smoothly as you turn it. To ensure proper operation, it's important to choose a knob and handle that match the doors you already have. If you don't have a matching knob then you'll have to purchase a replacement doorknob and latch plate.

To begin the replacement process, first examine the old knob or handle to find what screws hold it in place. If there aren't screws then you can use the screwdriver to insert the cover plate between the screws plate hidden behind it.

After taking the knob off examine it for indications of damage and rust. If the knob shows any dents or marks then you'll need clean it. Otherwise it shouldn't require any major work.

Now it's time to install the new knob. You must first study the two knobs to make sure that you've chosen the right one for the door. You should select one with an extended rod that's designed to lock into the rod mechanism of the second knob. Once you've put the new knob in the hole in the upvc door replacement lock and then carefully insert it into the latch.

Thread the latch plate screws downwards, then test the spring by pushing down on it several times. The latch should pop up every time. Install the second knob and secure it to the rod mechanism of the first knob. Then, thread the other long screws from the interior knob through the hole in the cylinder of the doorknob outside and secure it.

Latch

A latch is a metallic piece that extends into the door jamb to secure it closed. The latch can be operated by a knob or handle located inside the door, or a thumb-turn on the exterior. A deadbolt can be used to secure a latch and stop intruders from breaking through the glass of the door. It also protects against accidental or intentional closing of the door by pets or children. You can install a latch with either a single-cylinder or double-cylinder deadbolt depending on the level of security.

Installing a deadbolt can be the same as installing a latch but there are some differences. First, determine the setback of the doorjamb using an instrument to make sure that the new lock will fit. The setback is measured from the edge of doorjamb all the way to the center of hole for the latch plate. The standard setback is 2 3/8 to 2 3/4 inches. If your setback is larger, you may need to purchase a latch that is larger from a hardware or locksmith store.

Then, drill a hole for the latch plate in the edge of the doorjamb. Use a chisel and make the mortise for the latch. Make sure the depth is enough to allow the faceplate to be in line with the doorjamb. Put the strike plate into place to ensure that it's in the right position.

If the strike is too high, you could push the door back or apply pressure with the tire iron or crowbar. This can also cause the doorjamb's to crack. This can be fixed by drilling a new hole through the doorjamb, and chiseling the core out of the old one.

Installing the new strike plate is the final step. This can be accomplished by screwing the new plate into the existing screw holes. Then, use wood putty to cover the old screw holes and the bolt hole that is not used. After the putty has dried you can sand it until it has a smooth finish.

Strike

An electric strike is the metal piece where the deadbolt and latch engage when the door is shut. It is an essential component of the lock's security because it prevents the door from opening and provides an additional barrier to force or kicking. If a door is equipped with an electric strike, it will only be opened with an entry key or the control unit that governs its electrical impulses.

In the past, putting in an electronic strike was as simple as cutting a piece of a doorjamb to remove the latchbolt on a cylindrical lock from the pocket that is inside the strike. This modification is not just ugly however, it also exposes the mechanism of the latchbolt and the keeper to intruders.

Recently, several electric strikes manufacturers have come up with a "No Cut" type of strike that doesn't require a cutout in order to operate. They use a specific design that allows the latchbolt and keeper to slide into the pocket without causing damage to the faceplate of the doorjamb.

The strike is fitted with an internal ramp that lifts the latchbolt and keeper whenever it receives an indication from a reader. The latchbolt and keeper are pushed up the ramp due to retraction. When the door is shut, the deadbolt remains retracted, and the latchbolt retracts into the keeper.

Installing an electronic strike is a simple procedure, especially when you're replacing lock on upvc door an older strike. If, however, you are upgrading to an electric strike to use with an access control system, you will have to ensure that your new system is compatible with the kind of lock you've chosen to install. Also, you must ensure that the strike is wired to your access control system and that it is designed to operate in a fail-safe manner.

One method to guard against access by unauthorized persons is to upgrade the strike on your doors to a robust strike plate. These plates can be fitted with up to six screws of three inches instead of the standard two screws of three-fourths inches. The longer screws make it difficult for anyone to break the frame and then reach inside to turn the thumb turn piece of a single deadbolt cylinder.